Grinding & Cutting Equipment

Home/Pneumatic Tools and Equipment/Grinding & Cutting Equipment

ATS 2000’s Industrial Pneumatic Grinding And Cutting Equipment is Lubrication free and can cut & drill rails from 20kg – 60kg!

  • The ATS 2000 Turbo “G” 4 Pneumatic Utility Cutter with 340 Degree enclosed guard. The outstanding uncluttered side-to-centre of only 48mm which can produce a cut of 67mm vertical depth, and is the ideal tool for accurate and quick cutting off of excessively long roof bolts, jammed drill steels and cables. The ATS 2000 Pneumatic Utility Cutter has very good ergonomics and balance with a spade handle for better control in many positions, making the tool very user friendly. The motor produces 3kW and has exceptional torque and power even at low air pressures and has a light weight durable design with rust free components and a  stainless steel cylinder. The ATS 2000 Pneumatic Utility Cutter also has a built in safety latch trigger, is lubrication free, and has fail-safe governor that will not over speed. With the cut off wheel enclosed it is not possible to break or crack the wheel if the unit is dropped (a common problem experienced underground with the normal 50% open guard). The guard also contains most of the sparks in side the guard.  

    Download Brochure

  • The unique registered design of the ATS 2000 Pneumatic PVC and HDPE Chainsaw, allows for automatic precision leveling and aligning of the HDPE or PVC Pipe in relation to the frame via the chain-lock strap, which holds the HDPE or PVC pipe down while cutting is in process. There is a latch to hold the saw in the open position to allow the operator to load the timber into the frame. This makes the ATS Pneumatic PVC and HDPE Chainsaw a truly one man operated saw. Eliminating additional operators hands been caught in the saw. The ATS Pneumatic PVC and HDPE Chainsaw’ tungsten chain and guide bar remain cool, clean and lubricated while cutting and this gives them longer life and clean, non plastic balling repeatable cut time and time again. The ATS Pneumatic PVC and HDPE Chainsaw will cut HDPE pipes from 100mm to 450mm  

    Download Brochure

  • The ATS 2000 Turbo “G” 4 Pneumatic Rock Sampling Tool with adjustable flow on the water feed and 50% enclosed wheel guard and an outstanding uncluttered side to centre of only 46mm which can produce a cut of 67mm depth, and is the ideal tool for accurate and quick rock sampling and masonry cutting. The ATS 2000 Pneumatic Rock Sampling Tool has very good ergonomics and balance with a spade handle for better control in many positions, making the tool very user friendly. The motor power produces 3kW and has exceptional torque and power even at low air pressures and is of a light weight durable design with a stainless steel cylinder. The ATS 2000 Pneumatic Rock Sampling Tool has a built in safety latch trigger, is lubrication free, and a fail-safe governor that will not over speed.  

    Download Brochure

  • THE SOLUTION TO OVER SPEED AND GREATER SAFETY

    The greatest hazard condition of a Pneumatic Vertical & Horizontal Grinders is caused by over speed. 90% of over speed occurs in the off load condition. Malfunction due to wear and tear on the speed controller, which then allows the grinding wheel to run to speeds higher than the safety limits of the grinding wheel resulting in wheel failure disintegration and injury.

    TURBO G4 – RAPID RESPONSE SPEED CONTROLLER

    HOW IT WORKS

    The TURBO G4 bursts into life the second you switch on the safety lock throttle, running to the maximum safe permissible speed of the wheel. When the slightest load is applied the speed controller senses this and responds by increasing airflow with only a 3% reduction in speed under full load. Conventional speed controllers reduce speed by between 12% and 20% speed reduction under full load result in reducing power output, production and wheel life potential. Another great feature of the grinder’s speed controller is decreased motor speed with any increase in air pressure above design 6.2bar pressure (90psi), which is unique to the Turbo G4 rapid response governor.

    SAFETY BENEFITS

    • Greater safety because the motor speed does not increase with increase in air pressure
    • Greater safety as speed controller works in unison that is there are no stationary components acting against rotating components resulting in longer life of this vital assembly
    • Safety lever on throttle eliminates accidental activation

    AIR CONSUMPTION BENEFITS

    • Lower over-all consumption is achieved due to super-efficient motor and governor design.

    OTHER UNIQUE FEATURES

    • Lubrication-free technology
    • Excellent spares and service backup
    • BEST IN CLASS – Low weight and excellent power to weight ratio
    • Handles are ergonomically angled to reduce operator fatigue
    • Side-to-centre of body equals backing discs side-to-centre allowing full wheel potential for back grinding and cutting off operations
    • Safety lock throttle levers as standard
    • Detachable handles and motor cap for lower maintenance costs
    • Wide governed speed range: max 10200rpm – 3000rpm (ungeared) direct drive
    • Proudly designed and manufactured in South Africa
     

    Download Brochure

  • The unique registered design of the ATS 2000Timber Prop Pneumatic Chainsaw, allows for automatic precision leveling and aligning of the timber in relation to the frame via the spring loaded clamp down chain guard, which hold the timber down while cutting is in process. There is a latch that holds the saw in the open position to allow the operator to load the timber into the frame. This makes the ATS 2000 Timber Prop Pneumatic Chainsaw a truly one man operated saw. Eliminating additional operators hands been caught in the saw. A Double throttle hand control is an option for operators who want to guarantee that both hands have to be on the control handles to operate the Timber Prop Pneumatic Chainsaw. The Timber Prop Pneumatic Chainsaw cuts timber props from 200mm to 350mm in diameter.  

    Download Brochure

Go to Top